Carbide-Drill 8,0 x 200 mm

Hard Metal Drills with Carbide - Cone PointApplicable for all standard-uses in the locksmith field. The prizes refer respectively to a piece.Shank Diameter: 7,0 x 100 mm  

Hard Metal Drills with Carbide - Cone PointApplicable for all standard-uses in the locksmith field. The prizes refer respectively to a piece.Shank Diameter: 8,0 x 120 mm  

Hard Metal Drills with Carbide - Cone PointApplicable for all standard-uses in the locksmith field. The prizes refer respectively to a piece.Shank Diameter: 5,0 x 150 mm  

Attention! New Multipick Production!The new Laser Track key HU66 of Multipick’s latest production for car door openings of the brands: BMW E Serie, Land Rover and Range Rover with HU92, Citroën and Peugeot with HU83 cylinder, Fiat and Lancia with HU83 cylinder. Even more simple to use thanks to new profiling. The necessary exertion of force has been considerably reduced. The new Multipick product generation features a very high capacity and durability thanks to the especially hardened tool steel.Simply a precision tool "Made in Germany".  Specifications:Wrench size: 10 mmLength: 75 mmWeight: 0.028 kg 

The HOT SHOT Kit Prime-Cut has been revamped by BROCO.The manufacturer has added a spacious, higher quality carrying case that holds additional gear such as a regulator, clothing and everything else needed to get the job done. The welding gloves were also upgraded and the glasses were replaced with a protective mask. The central unit of the BROCO HOT SHOT kit Prime-Cut consists of the handle for the lances, which holds the burning rods with special collets and the integrated oxygen valve to regulate oxygen supply towards the end of the lances. The 3 meter long oxygen pipe, which is connected to the handle, is to be connected to a conventional oxygen pressure regulator. We screw the set together fitting to the European standards.(Pressure regulator and oxygen bottle are not included in the set)Functioning:The following articles and accessories are required to work with Hot-Shot thermic lances:Art-No 60300 - Hot-Shot KitBattery with min. 12 volt and 10 Ah. A battery for motorbikes with these characteristics is sufficient.Oxygen bottle (the size depends on the quantity of material you want to cut and existing means of transport /space.Pressure regulator for oxygenAppropriate quantity of thermic cutting rods for the planned application Connect the pressure regulator to the oxygen bottle and the end of the oxygen hose to the exit of the pressure reducer. The clamps of the strike plate and the handle of the tool are connected to the battery according to the colour code (red to +, blue to -). Select the appropriate cutting rod and collet depending on the object you want to cut. Unscrew the nut of the handle in order to place the collet then tighten the nut slightly. Now place the thermic rod in the collet (the hollow end of the rod must be placed in the collet/handle) and tighten the nut completely. Now open the valve of the oxygen bottle and adjust the level of oxygen pressure using the pressure reducer. Now touch the strike plate with the tip of the thermic rod in order to create short circuit sparks. Push the mechanism of the handle, in order to let the oxygen flow through the cutting rod and thus igniting the rod. It is possible to adjust the oxygen pressure again in order to start cutting. The higher the oxygen pressure /throughput, the higher the temperature at the tip of the rod. While higher temperature allows faster cutting it will also result in a faster burning of the thermic rod. In order to cut, place the tip of of the rod directly on the surface of the object you want to cut.  When selecting the thermic cutting rods to be used keep in mind that the diameter of the rod and the length of the rod, in combination with the oxygen pressure used, influence the speed of the cut. The oxygen pressure that is optimal depends on the material that is to be cut. The producer recommends the following approximate oxygen pressures for different types of metals: 0.6 - 1.4 bar for the punc  turing hard metal plates1.5 - 3.0 bar for the cutting of steel plates up to 0.7 mm thickness3.0 - 3.5 bar for the cutting of steel plates up to 15 mm thickness3.5 - 4.2 for the cutting of steel plates from 15 mm to 50 mm thickness4.2 - 5.5 for the cutting of steel plates over 50 mm thickness Unfortunately the producer does not give recommendations for the cutting of concrete, bullet proof glass or other materials. Users can quickly find out the optimal oxygen pressure through some short testing, though. 

This solid carbide high-speed drill of the latest generation is made of 100% carbide. It is the top product for cylinder openings in record time, and distinguishes itself in a high durability. For best results use a milling machine. Even with a drilling machine or a cordless screwdriver this cutting burr gives conspicuous service. In connexion with our high-performance grinding bits the user obtains an almost perfect and durable tool combination! With this drill the cylinder will be cut straight in very short time, no matter what kind of drilling protection you may find. Normally the cylinder should be possible to open by now. If it does not, you enlarge the existing whole sidewards with a grinding bit. Since this way of proceeding spares the tooth system of the grinding bit and besides is fast and efficient, we consider this combination of drill grinding bit and grinding bit as an ideal supplementOn top of our high performance cutting burrs a "must" for the equipment of every locksmith! Technical Data:Shaft-Ø: 6 mmLength: 60 mmCutting Length: 30 mm100% CarbideVery Long DurabilityBlue-Tec coated 

Special Drill Bits for Vaults (Hard Plate V Tip®) 8.5 x 105 mmThese special drill bits are very well suited for the drilling of very hard materials. With their special notched carbide tip they drill up to 50% faster through these types of materials compared to traditional drill bits.Shank Diameter: 6.05 mm