DBB-2 Morticer Set with 3 carbide tipped cutters

We have put together an unbeatable milling set for you! M4 Multipick's milling bag - A complete set for milling cylinders, but not just for fire brigades! Small, practical and safely packed - always ready to go! Technical data:Idle speed: 26.000 min-1Collet chuck: 6 mmApplication tool max.: 36 mmBattery voltage: 18 VDimensions (L x W x H) mm: 402 x 82 x 118Battery voltage: 18 VWeight: 2.0 kg 

The HOT SHOT Kit Prime-Cut has been revamped by BROCO.The manufacturer has added a spacious, higher quality carrying case that holds additional gear such as a regulator, clothing and everything else needed to get the job done. The welding gloves were also upgraded and the glasses were replaced with a protective mask. The central unit of the BROCO HOT SHOT kit Prime-Cut consists of the handle for the lances, which holds the burning rods with special collets and the integrated oxygen valve to regulate oxygen supply towards the end of the lances. The 3 meter long oxygen pipe, which is connected to the handle, is to be connected to a conventional oxygen pressure regulator. We screw the set together fitting to the European standards.(Pressure regulator and oxygen bottle are not included in the set)Functioning:The following articles and accessories are required to work with Hot-Shot thermic lances:Art-No 60300 - Hot-Shot KitBattery with min. 12 volt and 10 Ah. A battery for motorbikes with these characteristics is sufficient.Oxygen bottle (the size depends on the quantity of material you want to cut and existing means of transport /space.Pressure regulator for oxygenAppropriate quantity of thermic cutting rods for the planned application Connect the pressure regulator to the oxygen bottle and the end of the oxygen hose to the exit of the pressure reducer. The clamps of the strike plate and the handle of the tool are connected to the battery according to the colour code (red to +, blue to -). Select the appropriate cutting rod and collet depending on the object you want to cut. Unscrew the nut of the handle in order to place the collet then tighten the nut slightly. Now place the thermic rod in the collet (the hollow end of the rod must be placed in the collet/handle) and tighten the nut completely. Now open the valve of the oxygen bottle and adjust the level of oxygen pressure using the pressure reducer. Now touch the strike plate with the tip of the thermic rod in order to create short circuit sparks. Push the mechanism of the handle, in order to let the oxygen flow through the cutting rod and thus igniting the rod. It is possible to adjust the oxygen pressure again in order to start cutting. The higher the oxygen pressure /throughput, the higher the temperature at the tip of the rod. While higher temperature allows faster cutting it will also result in a faster burning of the thermic rod. In order to cut, place the tip of of the rod directly on the surface of the object you want to cut.  When selecting the thermic cutting rods to be used keep in mind that the diameter of the rod and the length of the rod, in combination with the oxygen pressure used, influence the speed of the cut. The oxygen pressure that is optimal depends on the material that is to be cut. The producer recommends the following approximate oxygen pressures for different types of metals: 0.6 - 1.4 bar for the punc  turing hard metal plates1.5 - 3.0 bar for the cutting of steel plates up to 0.7 mm thickness3.0 - 3.5 bar for the cutting of steel plates up to 15 mm thickness3.5 - 4.2 for the cutting of steel plates from 15 mm to 50 mm thickness4.2 - 5.5 for the cutting of steel plates over 50 mm thickness Unfortunately the producer does not give recommendations for the cutting of concrete, bullet proof glass or other materials. Users can quickly find out the optimal oxygen pressure through some short testing, though. 

For older style Jigs with ?Snap-on Cutters‘, an upgrade kit is available. Order 3 new style Carbide Wood Cutters and a Long Shaft and spanner come free. This Upgrade Kit comes with Carbide Tipped Cutters in a range of 16.2 mm , 20.0 mm and 23.8 mm. If you prefer other cutter sizes please contact us and we shall make an individual offer.   

With this cylinder gauge Multipick proposes a handy measuring tool to the professional locksmith. In only one process cylinder lock lengths on both sides are measurable fast and precisely.Solid Aluminium/Steel construction with easy readable length scale. For doors up to 180 mm thick.Weight: 180 grams 

The small bore kit has a housing which readily replaces the standard one and quickly allows the morticing for smaller locks. 

Attention! New Multipick Production!The new Laser Track key HU66 of Multipick’s latest production for car door openings of the brands: AUDI, SKODA, PORSCHE, SEAT, VW etc. Even more simple to use thanks to new profiling. The necessary exertion of force has been considerably reduced. The new Multipick product generation features a very high capacity and durability thanks to the especially hardened tool steel.Simply a precision tool "Made in Germany".  Specifications: Wrench size: 10 mmLength: 75 mmWeight: 0.028 kg 

Practical tool set for broken latches. Allows easy access of the broken latch. How to use:remove the escutcheonfix the latch, for ex. with the latch opening carduse the inner opening of the nut to center the jig saw to remove the nut.through the created opening the latch can be drawn back with the high-grade steel hook, even if the latch is blocked.