Door Spreader "Herkules"

This simple and very useful tool allows the user to pull down the door handle on the other side of the door. The Door Handle-Catch is simply inserted in the gap between door and floor, then lifted up and adjusted above (around) the door handle. Using the pulling-rope on the outside, the handle is then pushed down.  In many cases this is the easiest and fastest method of opening closed but unlocked doors. A necessary precondition for the successful use of the handle-catch is a sufficiently wide gap (at least 4.0 mm) between door and floor or a door-strip that can be removed to create a sufficiently wide gap. The door handle catch can also be used with double rebate doors.In combination with the Door Handle Catch, the Air-Wedge can be very efficient. Length of pulling rope: approx. 110 cm.The door handle catch can also be used with double rebate doors. 

The unbeatable Electric Lock Pick Set from Multipick!Outstanding quality from Germany!We are now also offering the popular Multipick Kronos EPG as a complete set with a large assortment of useful auxiliary tools. A hard-shell plastic case with appropriate recesses provides for secure storage; there is an additional small hinged plastic box for bits and pieces.The Kronos provides you with the most modern electronics coupled with a high-performance motor. Because of its low inherent vibrations, the Kronos is one of the most quiet (if not the most quiet) electric lock picks offered anywhere in the world. A genuine plus if you still have to be picking a cylinder lock in the early hours of the morning. Further we were able to convince one of the largest German manufacturers of DC motors to collaborate with us. Thanks to its newly designed power management system, the Kronos EPG is able to operate under steady load for more than two hours.Charging has never been so easy! Simply connect the accompanying USB cable via the included mains adapter or to a computer and recharge the Kronos without the tangle of various different cables. One single cable with many possibilities — that’s how we do it nowadays! An additional rechargeable battery delivers the needed “power” when the situation demands it. What’s more, the accompanying pick needles are manufactured out of exactly the same ingenious material as our ELITE lock picks.Important and useful accessories that one otherwise would have to buy separately, are also provided in this complete kit.So, to name just a few, there is the Circular Tensioner TNT-20-V3 for a quick change in the direction of tension. The TNT-20-V3 is the only circular tensioner anywhere in the world that offers the possibility of adapting precisely through a quick and tool-less change of the lower tension pin to different respectively curved cylinder profiles. Change pins for straight, left- and right-sided curved cylinder profiles are included as part of the delivered content.The Flip-It (Multipick-Original) - a further development with an extremely high utility value. With the new Flip-It, particular value was placed not just on its unusual design, but also on the mechanical precision of the “trigger system”. The mechanism in the new Flip-It makes it possible to “shot release” by just applying “light pressure” on the trigger button. The advantage this mechanism provides is that; one can work without the “exertion” that was generally necessary until now. This spinner thereby makes it possible to work very calmly and precisely.In addition to the standard ELITE pick needles (0.5 mm), a five piece needle set in 0.6 mm thickness is also provided. This thicker version is more forgiving of beginner mistakes by not breaking so quickly.Just take a look at everything that comes with this set — there are no more useful accessories than these!Nor would you expect anything less in this Kronos Complete Product Kit  “made in Germany” by Multipick. Technical specifications - Kronos:Li-Ion battery 3.7 V / 2900 mAhNeedle deflection precisely adjustable from 1 to 4 mm at the needle chuckIdle speed 13,000 rev/minWeight with battery - approx. 0.350kgDimensions: D=34 mm L=205 mmBattery life in continuous operation: approx. 2.5 hours 

The handle makes working much more comfortable and protects against injuries inside the hand by the edges of the opening cards. Assembling is easy: with a simple paper punch the card can be punched and fitted like a sandwich between the two handle parts the two crosshead screws and their counter nuts. 

The cutter is attached to a power drill, or a heavy duty cordless screwdriver. It enables the penetration of the hardened steel front plate of the Abloy high security cylinder, and removal of the plug behind.  Product Features:4 crosswise carbide tipped cutting tools (Ø 15.2 mm)spring loaded drill bit guide (6.8mm) for centring the plugoptimised depth stoptriangular shaft to fit 3 jawed chuckMade in Germany     

The perfect combination of a Euro profile cylinder and a Dimple cylinder - unique and only from Multipick Something that was impossible for most a while back is now becoming a reality: Controlled practice to overcome the difficulties of a Dimple cylinder and a Euro profile cylinder. Thanks to the modular structure and side slots, our training locks are perfect for educating yourself how to pick difficult cylinder locks, such as dimple and euro profile locks. This is the perfect training tool for lockpicking at home and at work. Dimple or Euro profile? - Both! This practice lock literally has two sides: One side features a Euro profile and the other a Dimple profile. Variation and versatility are the most important characteristics of this model. You can always choose the appropriate cylinder and only have to decide which profile you want to use. Even the standard pin version of this practice lock is quite a challenge and requires a lot of know-how to pick it. If you wish to increase the difficulty or make it less challenging, then you can decide for yourself the degree of difficulty at any time by means of the fastening screws. Re-pinning the practice lock is easy peasy: Simply loosen the grub screws with the provided allen key and replace the springs and pins. After that, simply screw the grub screws back in and your new challenge with your training lock is ready. The set contains the required set of pins including a pair of tweezers in the scope of delivery. In this way, you can instantly adapt your training cylinder to your own needs. This makes this exercise lock a real challenge with countless possibilities. Practice in a varied way to keep your skills improving. If you are looking for more challenges, you can order additional sets of pins in various sizes as accessories from our shop. These sets include many more key pins and driver pins as well as spool pins, security pins and springs, of course. For the best and most secure lockpicking practice, we recommend our Centurion vise. The Centurion provides a secure hold for your training cylinder and helps you to concentrate solely on picking. The cylinder in this set is slotted on one side. The other side is kept as it is in order to increase the level of difficulty. This gives you the choice of whether you want to exercise visually or without seeing anything. A training lock that offers a wide range of possibilities and will take your lockpicking skills to a new level. Without any exception, only very high quality and precise cylinder locks are used for the production. Brilliant and precise fine mechanics from Multipick - Made in Germany, Made in Bonn. Features:Complete super set with top accessories for added possibilitiesStart immediately and celebrate your first achievementsTrain like the pros - progress from novice to professionalBecome quickly successful - What you see is what you do - learn and understand!Compatible with our pinning kits available in our shop Dimensions: 30 / 10 / 30 mm When you use an electric lock pick gun with our practice locks, it is important to check the grub screws regularly because they can loosen due to the strong vibrations.  

Lifter for security-fittings usually allow lifting of the security fitting in order to insert a square bolt knife into the gap and turn the handle mechanism.Normally this opening technique is only possible with simple fittings which are not screwed together. The device of the “Bridge” lifter for fittings is fixed to the exterior door handle. On regular pulling by use of the screws the fitting comes off the door leaf by a few millimeters. The adapted square bolt knife will be inserted to the gap and the lock will be opened by turning the square bolt. NEW! Highly durable and long lasting construction. Big advantage due to new special trapezoidal thread which makes it easy to tighten - this prevents the thread from "seizing". The regular and smooth pulling of the fitting by the 2 screws of the Bridge should be careful since pressure marks of the tools’ feet may occur in case of inattention! The respective square bolt knives (8 mm and 10 mm) are included. Also this tool is very well adapted together with our emergency set for broken latch. A 17 mm driver is needed in order to turn the screws lifting the fitting! The “Bridge” differs essentially from the other lifters on the market in the following ways:Assembly of high-value aluminiumDespite new light weight construction extremely loadableVery solid finishingExtremely high durabilityOptimal exertion and distribution of pulling forceBig advantage due to new special trapezoidal threadQuick identification of bolt diameter through millimeter markings