Handle Lever for profile cylinders

Handle levers are important tools in cases of mechanical defects of the lock. Unfortunately this type of problem is very common and presents a great challenge to locksmiths. With the help of the door handle lever the latch can be activated by pushing down the handle on the other side of the door, thus opening the door. This unique tool, therefore, is a very simple solution to a difficult problem. Once the lock has been snapped out, the lever tool is inserted through the mortise lock as shown in the below diagram. The precisely calculated radius of the lever arm ensures easy insertion through the mortise lock. There it is thrown over the inside lever handle. After that, this can easily be actuated from the outside over the handle and the door can be opened quickly.  

Handle levers are important tools in cases of mechanical defects of the lock. Unfortunately this type of problem is very common and presents a great challenge to locksmiths. With the help of the door handle lever the latch can be activated by pushing down the handle on the other side of the door, thus opening the door. This unique tool, therefore, is a very simple solution to a difficult problem. 

This 900 g heavy double ended lever has been designed to create gaps between door and frame in order to insert latch wires, cards etc. The two ends of the tool have different shapes and in combination with the Latch Wire Tool allow the opening of doors opening to the inside or to the outside. Of course the tool also allows the insertion of any other type of latch tool. Length: 200 mmWidth; 40 mmWidth at tip: 60 mmWeight: 900 g 

The door lever is an easy to use tool for lifting up doors. Very suited when using the latch opener set for double-offset doors and in many other situations. 

This simple and very useful tool allows the user to pull down the door handle on the other side of the door. The Door Handle-Catch is simply inserted in the gap between door and floor, then lifted up and adjusted above (around) the door handle. Using the pulling-rope on the outside, the handle is then pushed down.  In many cases this is the easiest and fastest method of opening closed but unlocked doors. A necessary precondition for the successful use of the handle-catch is a sufficiently wide gap (at least 4.0 mm) between door and floor or a door-strip that can be removed to create a sufficiently wide gap. The door handle catch can also be used with double rebate doors.In combination with the Door Handle Catch, the Air-Wedge can be very efficient. Length of pulling rope: approx. 110 cm.The door handle catch can also be used with double rebate doors. 

The Multipick 30/30mm Euro profile cylinder with 6 pins, 3 keys and a mounting screw to mount on the door: Our cylinder lock is of very high-quality and high-precision craftsmanship. Use it as a replacement for a destroyed lock on a customer's premises or to improve your skills in milling or pulling cores. A cylinder with which you can't go wrong at this price-performance ratio.  

Lifter for security-fittings usually allow lifting of the security fitting in order to insert a square bolt knife into the gap and turn the handle mechanism.Normally this opening technique is only possible with simple fittings which are not screwed together. The device of the “Bridge” lifter for fittings is fixed to the exterior door handle. On regular pulling by use of the screws the fitting comes off the door leaf by a few millimeters. The adapted square bolt knife will be inserted to the gap and the lock will be opened by turning the square bolt. NEW! Highly durable and long lasting construction. Big advantage due to new special trapezoidal thread which makes it easy to tighten - this prevents the thread from "seizing". The regular and smooth pulling of the fitting by the 2 screws of the Bridge should be careful since pressure marks of the tools’ feet may occur in case of inattention! The respective square bolt knives (8 mm and 10 mm) are included. Also this tool is very well adapted together with our emergency set for broken latch. A 17 mm driver is needed in order to turn the screws lifting the fitting! The “Bridge” differs essentially from the other lifters on the market in the following ways:Assembly of high-value aluminiumDespite new light weight construction extremely loadableVery solid finishingExtremely high durabilityOptimal exertion and distribution of pulling forceBig advantage due to new special trapezoidal threadQuick identification of bolt diameter through millimeter markings