Milling Burr 6 x 50 / 16 mm - Ball nosed cylinder

This solid carbide milling burr 4 x 6 x 60 mm is cut off one piece. It distinguishes itself through rough drilling features, due to its deep cuts, which also leads to a good chipping removal.Special features:Due to the reduction of a 6 mm drill burr to 4 mm at the tip, working time is reduced by more than half, for less material has to be cut. A pleasant side effect: the core drawing protection doesn’t have to be destroyed thanks to the small milling burr head diameter. Technical features:Material: Solid carbide Form: cylindrical d1: 4.0 mm I1: 14.0 mm d2: 6.0 mm I2: 60 mm Toothing: crossed toothing for unsiversal use Coating: noneApplication possibilities:     tough and high-strength materialalloyed steel casting synthetic material    universal usagehighest chip removalStrongly recommended for the following materials:BrassCopperCast ironBronzePure steelHardened steelStainless steelHigh-Grade steelTitan 

This simple and very useful tool allows the user to pull down the door handle on the other side of the door. The Door Handle-Catch is simply inserted in the gap between door and floor, then lifted up and adjusted above (around) the door handle. Using the pulling-rope on the outside, the handle is then pushed down.  In many cases this is the easiest and fastest method of opening closed but unlocked doors. A necessary precondition for the successful use of the handle-catch is a sufficiently wide gap (at least 4.0 mm) between door and floor or a door-strip that can be removed to create a sufficiently wide gap. The door handle catch can also be used with double rebate doors.In combination with the Door Handle Catch, the Air-Wedge can be very efficient. Length of pulling rope: approx. 110 cm.The door handle catch can also be used with double rebate doors. 

The revolutionary new Universal-PRO cutting style  Up to 82% more material removal than our usual HP-3 universal cutting style. *Long tool life comes with high performance.Almost vibration-free and controlled work even under tough roughing conditions possible.Available in the latest GREEN-TEC coating technology for another significant increase in tool life. For all types of steel such as:- Cast iron- Steel <60 HRC- Stainless steel (INOX)- Nickel basis and titanium alloy- Also for copper, brass, bronzeSpecifications:Ø Shank: 6 mmTotal length: 50 mmCutting length: 18 mm * If the aggressive material removal / roughing of the new Universal-PRO cut appears too strong for you, please use our proven HP-3 universal cut. 

The Flip-It - a development with high utility value Now in a revamped version for even more precise triggering and better handling For the new Flip-It we did not only concentrate on an extraordinary design, but also on the mechanical precision of the trigger system. What always disturbed us with other plug spinners on the market was that they tend to jam when trigered, which prevents the free turning of the cylinder core over the dot. This problem is principally due to a careless finish of the trigger mechanism, often coupled with cumbersome fixation of the control element. The engineers of Multipick took over this problem into consideration and found a perfect solution. The mechanism of the new Flip-It enables the “shot” release, simply through a gentle push of the trigger button. The advantage is that you can work without the exertion that was generally necessary until now. This tool enables precise and calm working. The Flip-It impresses with its highly qualitative aircraft grade aluminium (EN AW-7075) production. This product, with its combination of spring steel, proved for durability, and rubber rings of silicium, for non-slip guaranty, is an absolute highlight and an essential tool for any Lock pickerFine precision engineering "Made in Germany" by ©Multipick  

This special tool developed for locksmiths and government agencies allows the easy and hassle-free removal of all types of cylinder locks (profile, round and oval cylinders). The ‘’Bell‘’ enables the door to be opened quickly without damaging the door or the fitting.In combination with the included core pulling plates, the cylinder core alone can be easily extracted from the housing so that the locking mechanism can be actuated without any difficulty. Especially with half cylinders, such as those found on glass doors, garage doors, alarm systems, shutters etc., to save time, deploying the "Bell" is often the only option when it comes to opening the door in an emergency. As the device works with a single and centrally oriented pulling-mechanism, there are no lateral forces during the actual pulling. This prevents the special extraction screws from jamming or snapping.For its compact and robust design and the effective mode of operation, the "Bell" is considered one of the best plug-pulling devices among professionals around the world. The "Bell" is made of hardened steel to ensure years of use.The tension rod is equipped with a hardened trapezoidal thread that enables precise operation and improved load bearing. Compared to the conventional fine thread, this new thread is more durable and allows faster and more precise operation without losing any torque due to the greater thread pitch. Furthermore, the rougher trapezoidal thread is less susceptible to brass shavings.If you should ever need spare parts, just give us a call! We constantly have all spare parts in stock.The "Bell" is one of the most important and essential tool for all emergency opening services.Care instructions for Multipick Bell (Please pay attention to these instructions!) Just like any other tool, our lock puller "Multipick Bell" also requires care. This means that the ball bearing and the tension rod as well as all moving parts should be kept free of metal shavings after each use and regularly treated with lubricating grease. You can either apply it by means of a brush or, alternatively, using a similar spray grease.