Assembly

The HOT SHOT Kit Prime-Cut has been revamped by BROCO.The manufacturer has added a spacious, higher quality carrying case that holds additional gear such as a regulator, clothing and everything else needed to get the job done. The welding gloves were also upgraded and the glasses were replaced with a protective mask. The central unit of the BROCO HOT SHOT kit Prime-Cut consists of the handle for the lances, which holds the burning rods with special collets and the integrated oxygen valve to regulate oxygen supply towards the end of the lances. The 3 meter long oxygen pipe, which is connected to the handle, is to be connected to a conventional oxygen pressure regulator. We screw the set together fitting to the European standards.(Pressure regulator and oxygen bottle are not included in the set)Functioning:The following articles and accessories are required to work with Hot-Shot thermic lances:Art-No 60300 - Hot-Shot KitBattery with min. 12 volt and 10 Ah. A battery for motorbikes with these characteristics is sufficient.Oxygen bottle (the size depends on the quantity of material you want to cut and existing means of transport /space.Pressure regulator for oxygenAppropriate quantity of thermic cutting rods for the planned application Connect the pressure regulator to the oxygen bottle and the end of the oxygen hose to the exit of the pressure reducer. The clamps of the strike plate and the handle of the tool are connected to the battery according to the colour code (red to +, blue to -). Select the appropriate cutting rod and collet depending on the object you want to cut. Unscrew the nut of the handle in order to place the collet then tighten the nut slightly. Now place the thermic rod in the collet (the hollow end of the rod must be placed in the collet/handle) and tighten the nut completely. Now open the valve of the oxygen bottle and adjust the level of oxygen pressure using the pressure reducer. Now touch the strike plate with the tip of the thermic rod in order to create short circuit sparks. Push the mechanism of the handle, in order to let the oxygen flow through the cutting rod and thus igniting the rod. It is possible to adjust the oxygen pressure again in order to start cutting. The higher the oxygen pressure /throughput, the higher the temperature at the tip of the rod. While higher temperature allows faster cutting it will also result in a faster burning of the thermic rod. In order to cut, place the tip of of the rod directly on the surface of the object you want to cut.  When selecting the thermic cutting rods to be used keep in mind that the diameter of the rod and the length of the rod, in combination with the oxygen pressure used, influence the speed of the cut. The oxygen pressure that is optimal depends on the material that is to be cut. The producer recommends the following approximate oxygen pressures for different types of metals: 0.6 - 1.4 bar for the punc  turing hard metal plates1.5 - 3.0 bar for the cutting of steel plates up to 0.7 mm thickness3.0 - 3.5 bar for the cutting of steel plates up to 15 mm thickness3.5 - 4.2 for the cutting of steel plates from 15 mm to 50 mm thickness4.2 - 5.5 for the cutting of steel plates over 50 mm thickness Unfortunately the producer does not give recommendations for the cutting of concrete, bullet proof glass or other materials. Users can quickly find out the optimal oxygen pressure through some short testing, though. 

This professional tool is very popular to locksmiths, alarm system fitters and joiners. For anyone who regularly fits mortice locks it will prove invaluable - an accurate, speedy and professional tool that will save time and money. The tool allows the finishing of a mortice in a few minutes without removing the door.Offset doors: DBB Morticer can also be used on offset doors. The housing has slits allowing it to move the right and to the left, giving it the possibility to work on offset and double offset doors. It also cuts for hinges and striking plates on door frames of 95 mm thickness maximum.You may easily produce mortices for hinges and striking plates on door frames. (maximumof 95mm thickness).Carbide Tipped Mortice Cutters for wood: Compared to the previous design, these improved carbide-tipped mortice cutters increase the cutting speed by up to 50% and keep their sharpness longer. The simplified screw-on ‘anti-lock’ design enables the cutter to be released quickly using the spanner provided. All in all there are twelve cutters available.Aluminium doors: Separately we offer 4 different sizes of aluminium cutters, allowing work on aluminium doors without any problem.Always wear gloves and safety glasses when working on metal!Plunging Cutters: These new cutters are ideal for installers who need perfectly drilled true holes. Ideal for the quick installation of Tubular Latches, Deadbolts, Concealed Door Closers etc. The range of 4 sizes of ‘Plunging Cutters’ are designed for locks where perfect installation is an issue. Made from High Speed Steel, these very effective 3 point plunging drills are a real bonus for those wanting to solve installation problems.Small Bore Kit: This system has been developed especially for small mortices. The smaller cutters require a thinner shaft and a special housing kit.Long Drill System: The long Drill Kit has been specifically designed for the easy installation of electric lock cables through wooden doors - from lock to hinge.After cutting the mortice you convert the morticer into the long drill system. Special geometry helps to keep the cutter 'on line' with minimal effort. The Long Drill Kit is a leader in its field. It is quick, accurate and easy to use. Characteristics:Cuts mortice for lock and face plate.Fast and accurate on doors from 40 mm - 85 mm thick.Increased cutting speed of up to 50% thanks to carbide tipped cutters.Cuts mortices for hinges, some striking plates and electric releases.The ‘anti-lock’ design enables the cutter to be released quickly.Uses vertical guides, height and depth stops to ensure precise cutting.Wide range of accessories.Robust construction and precision manufacturing.  Advantages:The morticer can be operated by one person.Doors don’t have to be removed which saves time and money.Increases accuracy and speed of mortice cutting.Can be used on wooden and aluminium doors.Only requires a power drill to work.  Technical details:Max. working depth for mortices: 180 mmMax. working depth for long whole mortices: 1250 mmMax. working depth for small whole mortices: 100 mmMax. thickness of door: all  Requirements for drilling machine or electric screw driver:Chuck: 13 mmRpm: 2000-3000  

With this cylinder gauge Multipick proposes a handy measuring tool to the professional locksmith. In only one process cylinder lock lengths on both sides are measurable fast and precisely.Solid Aluminium/Steel construction with easy readable length scale. For doors up to 180 mm thick.Weight: 180 grams 

Ideal accessory for the installation of new fittings, locks and cylinders. Essential tool for the exact adjustment of fitting, lock and cylinder for new installations. Length approx. 200 mm.