Special drill bit for vaults 6.8 x 305 mm

Special Drill Bits for Vaults (Hard Plate V Tip®) 10.0 x 165 mmThese special drill bits are very well suited for the drilling of very hard materials. With their special notched carbide tip they drill up to 50% faster through these types of materials compared to traditional drill bitsShank Diameter: 9.25 mm 

Important: This tool does not open locks with anti-pick system! Since this decoder is designed for double-bit lever lock Cisa/Gevy 3x3, its construction is accordingly. The pick consists of a rod with 3x3 pins. These pins are arranged in a specific order to match the intended lock. The pins are tightened in the back part of the handle by a pin manipulator. When this is tight, the pins will be difficult to move. If it is loose, the pins can be moved more easily. Preparation You take one of the two springs and put it into the slot in the front of the handle. Afterwards remove the cover of the housing (which is on the back). Then insert the rod into the handle as demonstrated in the video, and securely tighten it to the handle with the Allen key and insert the pin manipulator by screwing it into the back of the handle. The ease of movement of the pins is the most important thing. If they are tight, the opening process will not be successful! Lastly, mount the small tensioning handles. Now the decoder is ready for use. Opening and repairing procedure with the double-bit lock decoder Make sure that the decoder is used for the appropriate lock. Insert the tool with the pins that correspond to the position of the levers inside the lock. Now start the opening procedure. By tensioning it over the tensioning handles several times, the decoder raises each tumbler to a certain height so that the bolt can move. Finally, the pins "adopt" the position corresponding to the position of the "ridges" of the original key. Moreover, the double-bit lock decoder is easy to assemble and disassemble. Another important aspect is the ease of repairing a broken or twisted pin - simply unscrew the pin manipulator and replace the damaged pin. This lockpick tool works in a non-destructive way. Each tool can be used for a specific lock - in this case Cisa/Gevy 3x3 or for locks with similar dimensions. The internal dimensions of the locks (the size of the original key) are crucial. This means that you have to know the number of levers and the distance between the levers before using a lockpick tool. 

Special Drill Bits for Vaults (Hard Plate V Tip®) 10.0 x 204 mmThese special drill bits are very well suited for the drilling of very hard materials. With their special notched carbide tip they drill up to 50% faster through these types of materials compared to traditional drill bits.Shank Diameter: 9.25 mm 

Special Drill Bits for Vaults (Hard Plate V Tip®) 8.5 x 165 mmThese special drill bits are very well suited for the drilling of very hard materials. With their special notched carbide tip they drill up to 50% faster through these types of materials compared to traditional drill bits.Shank Diameter: 6.05 mm 

The HOT SHOT Kit Prime-Cut has been revamped by BROCO.The manufacturer has added a spacious, higher quality carrying case that holds additional gear such as a regulator, clothing and everything else needed to get the job done. The welding gloves were also upgraded and the glasses were replaced with a protective mask. The central unit of the BROCO HOT SHOT kit Prime-Cut consists of the handle for the lances, which holds the burning rods with special collets and the integrated oxygen valve to regulate oxygen supply towards the end of the lances. The 3 meter long oxygen pipe, which is connected to the handle, is to be connected to a conventional oxygen pressure regulator. We screw the set together fitting to the European standards.(Pressure regulator and oxygen bottle are not included in the set)Functioning:The following articles and accessories are required to work with Hot-Shot thermic lances:Art-No 60300 - Hot-Shot KitBattery with min. 12 volt and 10 Ah. A battery for motorbikes with these characteristics is sufficient.Oxygen bottle (the size depends on the quantity of material you want to cut and existing means of transport /space.Pressure regulator for oxygenAppropriate quantity of thermic cutting rods for the planned application Connect the pressure regulator to the oxygen bottle and the end of the oxygen hose to the exit of the pressure reducer. The clamps of the strike plate and the handle of the tool are connected to the battery according to the colour code (red to +, blue to -). Select the appropriate cutting rod and collet depending on the object you want to cut. Unscrew the nut of the handle in order to place the collet then tighten the nut slightly. Now place the thermic rod in the collet (the hollow end of the rod must be placed in the collet/handle) and tighten the nut completely. Now open the valve of the oxygen bottle and adjust the level of oxygen pressure using the pressure reducer. Now touch the strike plate with the tip of the thermic rod in order to create short circuit sparks. Push the mechanism of the handle, in order to let the oxygen flow through the cutting rod and thus igniting the rod. It is possible to adjust the oxygen pressure again in order to start cutting. The higher the oxygen pressure /throughput, the higher the temperature at the tip of the rod. While higher temperature allows faster cutting it will also result in a faster burning of the thermic rod. In order to cut, place the tip of of the rod directly on the surface of the object you want to cut.  When selecting the thermic cutting rods to be used keep in mind that the diameter of the rod and the length of the rod, in combination with the oxygen pressure used, influence the speed of the cut. The oxygen pressure that is optimal depends on the material that is to be cut. The producer recommends the following approximate oxygen pressures for different types of metals: 0.6 - 1.4 bar for the punc  turing hard metal plates1.5 - 3.0 bar for the cutting of steel plates up to 0.7 mm thickness3.0 - 3.5 bar for the cutting of steel plates up to 15 mm thickness3.5 - 4.2 for the cutting of steel plates from 15 mm to 50 mm thickness4.2 - 5.5 for the cutting of steel plates over 50 mm thickness Unfortunately the producer does not give recommendations for the cutting of concrete, bullet proof glass or other materials. Users can quickly find out the optimal oxygen pressure through some short testing, though. 

Hard Metal Drills with Carbide - Cone PointApplicable for all standard-uses in the locksmith field. The prizes refer respectively to a piece.Shank Diameter: 13,0 x 600 mm  

Universal drill with 10.0 mm drilling diameter, drilling length 200 mm, total length 260 mm, adapted for all drill hammers with SDS-plus and HILTI TE-C socket