Double-bit decoder for Metem 3x3

Important: This tool does not open locks with anti-pick system! Since this decoder is designed for double-bit lever Nucleo Compact 6, its construction is accordingly. The pick consists of a rod with 6 pins. These pins are arranged in a specific order to match the intended lock. The pins are tightened in the back part of the handle by a pin manipulator. When this is tight, the pins will be difficult to move. If it is loose, the pins can be moved more easily. Preparation You take one of the two springs and put it into the slot in the front of the handle. Afterwards remove the cover of the housing (which is on the back). Then insert the rod into the handle as demonstrated in the video, and securely tighten it to the handle with the Allen key and insert the pin manipulator by screwing it into the back of the handle. The ease of movement of the pins is the most important thing. If they are tight, the opening process will not be successful! Lastly, mount the small tensioning handles. Now the decoder is ready for use. Opening and repairing procedure with the double-bit lock decoder Make sure that the decoder is used for the appropriate lock. Insert the tool with the pins that correspond to the position of the levers inside the lock. Now start the opening procedure. By tensioning it over the tensioning handles several times, the decoder raises each tumbler to a certain height so that the bolt can move. Finally, the pins "adopt" the position corresponding to the position of the "ridges" of the original key. Moreover, the double-bit lock decoder is easy to assemble and disassemble. Another important aspect is the ease of repairing a broken or twisted pin - simply unscrew the pin manipulator and replace the damaged pin. This lockpick tool works in a non-destructive way. Each tool can be used for a specific lock - in this case Nucleo Compact 6 or for locks with similar dimensions. The internal dimensions of the locks (the size of the original key) are crucial. This means that you have to know the number of levers and the distance between the levers before using a lockpick tool. 

Important: This tool does not open locks with anti-pick system! Since this decoder is designed for double-bit lever lock Ezcurra /Fiam 6x6, its construction is accordingly. The pick consists of a rod with 6x6 pins. These pins are arranged in a specific order to match the intended lock. The pins are tightened in the back part of the handle by a pin manipulator. When this is tight, the pins will be difficult to move. If it is loose, the pins can be moved more easily. Preparation You take one of the two springs and put it into the slot in the front of the handle. Afterwards remove the cover of the housing (which is on the back). Then insert the rod into the handle as demonstrated in the video, and securely tighten it to the handle with the Allen key and insert the pin manipulator by screwing it into the back of the handle. The ease of movement of the pins is the most important thing. If they are tight, the opening process will not be successful! Lastly, mount the small tensioning handles. Now the decoder is ready for use. Opening and repairing procedure with the double-bit lock decoder Make sure that the decoder is used for the appropriate lock. Insert the tool with the pins that correspond to the position of the levers inside the lock. Now start the opening procedure. By tensioning it over the tensioning handles several times, the decoder raises each tumbler to a certain height so that the bolt can move. Finally, the pins "adopt" the position corresponding to the position of the "ridges" of the original key. Moreover, the double-bit lock decoder is easy to assemble and disassemble. Another important aspect is the ease of repairing a broken or twisted pin - simply unscrew the pin manipulator and replace the damaged pin. This lockpick tool works in a non-destructive way. Each tool can be used for a specific lock - in this case Ezcurra /Fiam 6x6 or for locks with similar dimensions. The internal dimensions of the locks (the size of the original key) are crucial. This means that you have to know the number of levers and the distance between the levers before using a lockpick tool. 

Important: This tool does not open locks with anti-pick system! Since this decoder is designed for double-bit lever lock IDM 3x3, its construction is accordingly. The pick consists of a rod with 3x3 pins. These pins are arranged in a specific order to match the intended lock. The pins are tightened in the back part of the handle by a pin manipulator. When this is tight, the pins will be difficult to move. If it is loose, the pins can be moved more easily. Preparation You take one of the two springs and put it into the slot in the front of the handle. Afterwards remove the cover of the housing (which is on the back). Then insert the rod into the handle as demonstrated in the video, and securely tighten it to the handle with the Allen key and insert the pin manipulator by screwing it into the back of the handle. The ease of movement of the pins is the most important thing. If they are tight, the opening process will not be successful! Lastly, mount the small tensioning handles. Now the decoder is ready for use. Opening and repairing procedure with the double-bit lock decoder Make sure that the decoder is used for the appropriate lock. Insert the tool with the pins that correspond to the position of the levers inside the lock. Now start the opening procedure. By tensioning it over the tensioning handles several times, the decoder raises each tumbler to a certain height so that the bolt can move. Finally, the pins "adopt" the position corresponding to the position of the "ridges" of the original key. Moreover, the double-bit lock decoder is easy to assemble and disassemble. Another important aspect is the ease of repairing a broken or twisted pin - simply unscrew the pin manipulator and replace the damaged pin. This lockpick tool works in a non-destructive way. Each tool can be used for a specific lock - in this case IDM 3x3 or for locks with similar dimensions. The internal dimensions of the locks (the size of the original key) are crucial. This means that you have to know the number of levers and the distance between the levers before using a lockpick tool. 

Important: This tool does not open locks with anti-pick system! Since this decoder is designed for double-bit lever lock MCM 3x3, its construction is accordingly. The pick consists of a rod with 3x3 pins. These pins are arranged in a specific order to match the intended lock. The pins are tightened in the back part of the handle by a pin manipulator. When this is tight, the pins will be difficult to move. If it is loose, the pins can be moved more easily. Preparation You take one of the two springs and put it into the slot in the front of the handle. Afterwards remove the cover of the housing (which is on the back). Then insert the rod into the handle as demonstrated in the video, and securely tighten it to the handle with the Allen key and insert the pin manipulator by screwing it into the back of the handle. The ease of movement of the pins is the most important thing. If they are tight, the opening process will not be successful! Lastly, mount the small tensioning handles. Now the decoder is ready for use. Opening and repairing procedure with the double-bit lock decoder Make sure that the decoder is used for the appropriate lock. Insert the tool with the pins that correspond to the position of the levers inside the lock. Now start the opening procedure. By tensioning it over the tensioning handles several times, the decoder raises each tumbler to a certain height so that the bolt can move. Finally, the pins "adopt" the position corresponding to the position of the "ridges" of the original key. Moreover, the double-bit lock decoder is easy to assemble and disassemble. Another important aspect is the ease of repairing a broken or twisted pin - simply unscrew the pin manipulator and replace the damaged pin. This lockpick tool works in a non-destructive way. Each tool can be used for a specific lock - in this case MCM 3x3 or for locks with similar dimensions. The internal dimensions of the locks (the size of the original key) are crucial. This means that you have to know the number of levers and the distance between the levers before using a lockpick tool. 

The new SECUREMME 3+3 automatic opener sets new standards in the opening technology of double-bit locks and opens the following: ALL Securemme 3+3 door locks with 2 and 4 turn pins (cam) and some safe lock models, common and SECURMAP ANTI-PICK modelsSecuremme 2, 4 and SAFE lock SECURMAP 11 modelsAkarsan 3×3 - locks with 2 turn pins (cam) - needs to be verifiedAcarsan 3×3 - locks with 4 turn pins (cam) - needs to be verifiedSteel 3×3 - with 2 turn pins (cam) - needs to be verifiedThe straightforward and secure operation ensures that unlocking is practically a piece of cake.After opening, a working key can be created.It only needs a little bit of practice and know-how to be able to use it successfullyPlease make sure to refer to the operating manual or the instructions video before use!We ensure 1 year warranty when used properlyExpress maintenance and repair in case of damage Additional video tutorials are available on YouTube! 

HPC - Replacement-Extractor - Wave 1,3 mm Replacement tool for HPC-Extractor set 5 pieces (Art.-No 3105)  

The ELITE G-PRO are the ultimate dimple lock picks, designed  for the professional lock picker.The highest-quality manufacturing and the finest materials allow unprecedented feedback when picking.The ELITE G-PRO is distinguished by its outstanding quality:finest polished tips in many variations for the widest variety of locksmaximum feedback - maximum transfer of pin behaviour to the userextremely stable, yet light and easy to handle, just like a springmicroelliptic blade shanks in various diameters for the perfect turning pointnon-slip, fatigue-free and lightweight handles made of the finest rubberized aluminiumexchangeable and individually available tips to safeguard the investment100% made in Germany.Specifications:Flag length: 2.30mmFlag width: 1.80mmFlag outreach: 0.50mmFlag orientation: rightShank radius - Ø: 0.85mmShank length: 95.0mmShank diameter: 8.0mmTotal length: 130.0mmWeight: 11g