STS 5 pins Topolino Decoder

Manual TOPOLINO Decoder for STS 6 pins This Topolino Decoder is constructed with a specific structure for the STS 6 pins</strong cylinder lock and consists of a blade with six uniquely positioned decoder pins. By deploying the TOPOLINO Decoder, you decode the profile of the key in just a few steps and can thus open the cylinder lock in the same easy way as with the original key. Please make sure to use it in a professional way, otherwise the opening ability of the cylinder and / or the tool may be affected. 

This pulling device is the small version of our plug-pulling device “Bell”. Its small size in combination with our V-PRO pull-screws allows the pulling out of the plugs of car locks. The locking mechanism can then be activated easily.Exterior diameter 3.0 cmInterior diameter 2.5 cm 

Opening tool for ISEO locks having 6 pumps.The straightforward and secure operation ensures that unlocking is practically a piece of cake.After opening, a working key can be created.It only needs a little bit of practice and know-how to be able to use it successfullyPlease make sure to refer to the instructions video before use!We ensure 1-year warranty when used properlyExpress maintenance and repair in case of damage Additional video tutorials are available on YouTube! 

The HOT SHOT Kit Prime-Cut has been revamped by BROCO.The manufacturer has added a spacious, higher quality carrying case that holds additional gear such as a regulator, clothing and everything else needed to get the job done. The welding gloves were also upgraded and the glasses were replaced with a protective mask. The central unit of the BROCO HOT SHOT kit Prime-Cut consists of the handle for the lances, which holds the burning rods with special collets and the integrated oxygen valve to regulate oxygen supply towards the end of the lances. The 3 meter long oxygen pipe, which is connected to the handle, is to be connected to a conventional oxygen pressure regulator. We screw the set together fitting to the European standards.(Pressure regulator and oxygen bottle are not included in the set)Functioning:The following articles and accessories are required to work with Hot-Shot thermic lances:Art-No 60300 - Hot-Shot KitBattery with min. 12 volt and 10 Ah. A battery for motorbikes with these characteristics is sufficient.Oxygen bottle (the size depends on the quantity of material you want to cut and existing means of transport /space.Pressure regulator for oxygenAppropriate quantity of thermic cutting rods for the planned application Connect the pressure regulator to the oxygen bottle and the end of the oxygen hose to the exit of the pressure reducer. The clamps of the strike plate and the handle of the tool are connected to the battery according to the colour code (red to +, blue to -). Select the appropriate cutting rod and collet depending on the object you want to cut. Unscrew the nut of the handle in order to place the collet then tighten the nut slightly. Now place the thermic rod in the collet (the hollow end of the rod must be placed in the collet/handle) and tighten the nut completely. Now open the valve of the oxygen bottle and adjust the level of oxygen pressure using the pressure reducer. Now touch the strike plate with the tip of the thermic rod in order to create short circuit sparks. Push the mechanism of the handle, in order to let the oxygen flow through the cutting rod and thus igniting the rod. It is possible to adjust the oxygen pressure again in order to start cutting. The higher the oxygen pressure /throughput, the higher the temperature at the tip of the rod. While higher temperature allows faster cutting it will also result in a faster burning of the thermic rod. In order to cut, place the tip of of the rod directly on the surface of the object you want to cut.  When selecting the thermic cutting rods to be used keep in mind that the diameter of the rod and the length of the rod, in combination with the oxygen pressure used, influence the speed of the cut. The oxygen pressure that is optimal depends on the material that is to be cut. The producer recommends the following approximate oxygen pressures for different types of metals: 0.6 - 1.4 bar for the punc  turing hard metal plates1.5 - 3.0 bar for the cutting of steel plates up to 0.7 mm thickness3.0 - 3.5 bar for the cutting of steel plates up to 15 mm thickness3.5 - 4.2 for the cutting of steel plates from 15 mm to 50 mm thickness4.2 - 5.5 for the cutting of steel plates over 50 mm thickness Unfortunately the producer does not give recommendations for the cutting of concrete, bullet proof glass or other materials. Users can quickly find out the optimal oxygen pressure through some short testing, though. 

Manual Topolino to decode PREFER roller shutter locks This Topolino Decoder is designed with a structure specific for PREFER roller shutter lock consisting of a blade with six specially arranged decoding pins. By using this Topolino Decoder, you can quickly read the profile of the key and open the lock with just a few clicks in the same manner as with the original key. A fantastic, easy-to-use tool with a very high opening success rate. Please make sure that you use the tool properly, otherwise the ability to open the lock cylinder and / or the tool can be affected. 

The Lock Noob Triple Gauge Pick Set 0.4 to 0.6 mm is a special compilation of our ELITE picks in gauges of 0.4 mm, 0.5 mm and 0.6 mm. This 15-piece set covers a broad spectrum of picks to ensure that you are well equipped to handle tricky situations. The British lock picking professional Lock Noob came up with this set based on his hands-on experience and it is perfect for challenging keyways. The pick collection is a must-have for lock pickers in either the USA or Europe. Further, based on his extensive knowledge, this kit will provide you an added benefit for successfully picking locks. What this kit offers:Comes with a genuine leather caseThe ultimate Lock Noob Pick Set in worldwide unrivaled qualityA unique pick set suitable for European and North American cylindersFinest blades - ingenious spring steel - perfect workmanshipHigh-quality individual design - perfection down to the last detailNo duplicate picks100% Made in Germany - by Multipick, of course 

Manual TOPOLINO Decoder for ABUS D10This Topolino Decoder is constructed with a specific structure for the ABUS D10 cylinder lock and consists of a blade with six uniquely positioned decoder pins.By deploying the TOPOLINO Decoder, you decode the profile of the key in just a few steps and can thus open the cylinder lock in the same easy way as with the original key.Please make sure to use it in a professional way, otherwise the opening ability of the cylinder and / or the tool may be affected.