Emergency Set for Broken Latch

This simple and very useful tool allows the user to pull down the door handle on the other side of the door. The Door Handle-Catch is simply inserted in the gap between door and floor, then lifted up and adjusted above (around) the door handle. Using the pulling-rope on the outside, the handle is then pushed down.  In many cases this is the easiest and fastest method of opening closed but unlocked doors. A necessary precondition for the successful use of the handle-catch is a sufficiently wide gap (at least 4.0 mm) between door and floor or a door-strip that can be removed to create a sufficiently wide gap. The door handle catch can also be used with double rebate doors.In combination with the Door Handle Catch, the Air-Wedge can be very efficient. Length of pulling rope: approx. 110 cm.The door handle catch can also be used with double rebate doors. 

Opening-Set for single- and double-offset doorsEvery locksmith knows the problem of closed double-offset doors. The new ACE spiral needles, made of high quality spring steel, allow the non-destructive opening of double-offset doors in most cases. The use is very simple: The tool is inserted in the narrow gap between door and frame by turning until it makes contact with the latch. Continued turning pushes back the latch. Usually this process does not cause any damages except a pierced sealing strip. The set consists of four (4) different tools for doors with the lock mounted either on the right or on the left and 2 different material strengths (1.5 and 1.7 mm) for the different types of offset door designs. Of course, the ACE-tools are very well suited for opening simple offset doors as well!For very tightly engaging (closing) double and simple offset doors the ACE-Mini-Set (2 pieces) of only 1.25 mm needle-strength is especially suited. 

Lifter for security-fittings usually allow lifting of the security fitting in order to insert a square bolt knife into the gap and turn the handle mechanism.Normally this opening technique is only possible with simple fittings which are not screwed together. The device of the “Bridge” lifter for fittings is fixed to the exterior door handle. On regular pulling by use of the screws the fitting comes off the door leaf by a few millimeters. The adapted square bolt knife will be inserted to the gap and the lock will be opened by turning the square bolt. NEW! Highly durable and long lasting construction. Big advantage due to new special trapezoidal thread which makes it easy to tighten - this prevents the thread from "seizing". The regular and smooth pulling of the fitting by the 2 screws of the Bridge should be careful since pressure marks of the tools’ feet may occur in case of inattention! The respective square bolt knives (8 mm and 10 mm) are included. Also this tool is very well adapted together with our emergency set for broken latch. A 17 mm driver is needed in order to turn the screws lifting the fitting! The “Bridge” differs essentially from the other lifters on the market in the following ways:Assembly of high-value aluminiumDespite new light weight construction extremely loadableVery solid finishingExtremely high durabilityOptimal exertion and distribution of pulling forceBig advantage due to new special trapezoidal threadQuick identification of bolt diameter through millimeter markings    

The cutter is attached to a power drill, or a heavy duty cordless screwdriver. It enables the penetration of the hardened steel front plate of the Abloy high security cylinder, and removal of the plug behind.  Product Features:4 crosswise carbide tipped cutting tools (Ø 15.2 mm)spring loaded drill bit guide (6.8mm) for centring the plugoptimised depth stoptriangular shaft to fit 3 jawed chuckMade in Germany     

The LockOff  Door Peephole Opener Kit - Now Being Manufactured By MultipickFrom now on, the LockOff door peep hole opener kit will be manufactured by Multipick in superior Multipick quality. However, we have kept the ingenious basic construction of the tool and simply reinforced the established weaknesses substantially. The Multipick LockOff has finally transitioned into a mature and durable tool, made in Germany.Thanks to its sophisticated system, this high-quality lever tool allows the opening of locked doors, whether single or double-rebated. It is particularly effective for opening self-locking doors.The included auxiliary tools, such as the “Special Pliers” and the “Peephole  Turbo-Helper”, which come in a high-quality shoulder bag for convenient transport and storage, are sufficient to open a door in the “blink of an eye” without causing any damage.In our opinion, this opening tool should be a “must have” component of in the professional equipment carried by emergency key services.Operation: Before using this tool, you should find out which type of door handle is installed. Unfortunately, rotary door knobs are also not operable with this opening tool. First, the length of the LockOff  lever arm must be adjusted. To do this, it's necessary to re-adjust and fix the LockOff rod, adjusting it from the center of the peephole to a position in relation to its distance to the door handle. The angled lever arm rests on the inside door handle. The rubber stopper on its tip prevents damage in case it hits the door. The door handle can be operated by pressing on the outside arm. The calibration of the lever arm in front of the door is very important! If it's too short, the lever slips off the handle before it can be pressed down sufficiently. If it's too long, one cannot generate enough force to press the lever down. In case of misalignment, the inserted LockOff can easily be pulled out and re-adjusted. The door peephole can also be easily removed from the outside with the special cranked pliers; take care to prevent scratches when the pliers slide off onto the door panel. With the LockOff – Peephole Turbo-Helper developed by us, you can remove all standard door peepholes without causing any destructive damage, in no time at all. Simply clamp it into a drill or screwdriver and “unscrew” the peephole with the necessary counter-pressure.Also, from now on, we will be offering a cost-effective modification, or repair  of your old LockOff. at a fixed price. All components with proven vulnerabilities will be replaced by new Multipick components, giving you a more robust and durable tool, including free express return shipping.Images may differ from original. 

The Multipick magnetic lifter is characterised by its versatility. Thanks to its telescopic design, the magnetic staff can be extended from a compact length of 11.5 cm up to 50 cm for flexibility.It is made of high-quality chrome-plated metal and is fitted with a strong magnet at its tip to draw ferromagnetic metal pieces out of a cylinder or a broken or milled cylinder, as well as to remove small pieces of metal residue from the cylinder receptacle after use with our V-Pro extraction screws.The corrosion-resistant and durable material ensures a long service life. A practical feature is the integrated pocket clip, which makes the magnetic lifter to be transported easily. This means it can be comfortably taken along with you for any job, especially at the customer's premises.