Offset Doors

The LockOff  Door Peephole Opener Kit - Now Being Manufactured By MultipickFrom now on, the LockOff door peep hole opener kit will be manufactured by Multipick in superior Multipick quality. However, we have kept the ingenious basic construction of the tool and simply reinforced the established weaknesses substantially. The Multipick LockOff has finally transitioned into a mature and durable tool, made in Germany.Thanks to its sophisticated system, this high-quality lever tool allows the opening of locked doors, whether single or double-rebated. It is particularly effective for opening self-locking doors.The included auxiliary tools, such as the “Special Pliers” and the “Peephole  Turbo-Helper”, which come in a high-quality shoulder bag for convenient transport and storage, are sufficient to open a door in the “blink of an eye” without causing any damage.In our opinion, this opening tool should be a “must have” component of in the professional equipment carried by emergency key services.Operation: Before using this tool, you should find out which type of door handle is installed. Unfortunately, rotary door knobs are also not operable with this opening tool. First, the length of the LockOff  lever arm must be adjusted. To do this, it's necessary to re-adjust and fix the LockOff rod, adjusting it from the center of the peephole to a position in relation to its distance to the door handle. The angled lever arm rests on the inside door handle. The rubber stopper on its tip prevents damage in case it hits the door. The door handle can be operated by pressing on the outside arm. The calibration of the lever arm in front of the door is very important! If it's too short, the lever slips off the handle before it can be pressed down sufficiently. If it's too long, one cannot generate enough force to press the lever down. In case of misalignment, the inserted LockOff can easily be pulled out and re-adjusted. The door peephole can also be easily removed from the outside with the special cranked pliers; take care to prevent scratches when the pliers slide off onto the door panel. With the LockOff – Peephole Turbo-Helper developed by us, you can remove all standard door peepholes without causing any destructive damage, in no time at all. Simply clamp it into a drill or screwdriver and “unscrew” the peephole with the necessary counter-pressure.Also, from now on, we will be offering a cost-effective modification, or repair  of your old LockOff. at a fixed price. All components with proven vulnerabilities will be replaced by new Multipick components, giving you a more robust and durable tool, including free express return shipping.Images may differ from original. 

The New Door Peephole Opener Lockoff - Now Being Manufactured By MultipickFrom now on, the door peephole opener LockOff will be manufactured by Multipick in superior Multipick quality. However, we have kept the ingenious basic construction of the tool and simply reinforced the established weaknesses substantially. The Multipick LockOff has finally transitioned into a mature and durable tool, made in Germany.Thanks to its sophisticated system, this high-quality lever tool allows the opening of locked doors, whether single or double-rebated. It is particularly effective for opening self-locking doors. In our opinion, this opening tool should be a “must have” component of in the professional equipment carried by emergency key services.Operation: Before using this tool, you should find out which type of door handle is installed. Unfortunately, rotary door knobs are also not operable with this opening tool. First, the length of the LockOff  lever arm must be adjusted. To do this, it's necessary to re-adjust and fix the LockOff rod, adjusting it from the center of the peephole to a position in relation to its distance to the door handle. The angled lever arm rests on the inside door handle. The rubber stopper on its tip prevents damage in case it hits the door. The door handle can be operated by pressing on the outside arm. The calibration of the lever arm in front of the door is very important! If it's too short, the lever slips off the handle before it can be pressed down sufficiently. If it's too long, one cannot generate enough force to press the lever down. In case of misalignment, the inserted LockOff can easily be pulled out and re-adjusted. The door peephole can also be easily removed from the outside with the special cranked pliers; take care to prevent scratches when the pliers slide off onto the door panel. With the LockOff - Peephole Turbo-Helper developed by us, you can remove all standard door peepholes without causing any destructive damage, in no time at all. Simply clamp it into a drill or screwdriver and “unscrew” the peephole with the necessary counter-pressure.Going forward, we will be offering a cost-effective modification, or repair  of your old LockOff. at a fixed price. All components with proven vulnerabilities will be replaced by new Multipick components, giving you a more robust and durable tool, including free express return shipping.Images may differ from original. 

Door Spreader "Hercules" - A spreader for heavy duty use When rapid access is required or conventional tools fail, the Door-Spreader "Hercules" is the appropriate tool to either create a gap between door and frame, or lift up the door to insert the tools allowing to solve the problem or defect. This very massive and robust tool creates the necessary gap quickly and can even be used to push open terrace doors, unlocked PVC and metal doors or to achieve forceful entry pushing out the hinges etc. A wrench or our gear wrench is required to turn the nut of the mechanism. This door spreader has originally been designed for emergency and law enforcement units. 

The Tilting Window Opener "Genius" with its new draw string of sturdy nylon for bent window handles. This new window opener, patent pending, opens 99% of all tilt & turn windows without great difficulties. Guaranteed. No suction cup is required. Included are one snare for an angled window handles and a bent lead rod allowing the insertion of the Genius in very tight gaps. An illustrated and easy to understand German manual is also included.Now you can also order the "Genius Repair Kit" through us, consisting of 2 sturdy nylon ribbon cables and 5 repair press clamps that can be used to repair your “Genius” with just a few taps from a hammer. (Article: 33969) 

Lifter for security-fittings usually allow lifting of the security fitting in order to insert a square bolt knife into the gap and turn the handle mechanism.Normally this opening technique is only possible with simple fittings which are not screwed together. The device of the “Bridge” lifter for fittings is fixed to the exterior door handle. On regular pulling by use of the screws the fitting comes off the door leaf by a few millimeters. The adapted square bolt knife will be inserted to the gap and the lock will be opened by turning the square bolt. NEW! Highly durable and long lasting construction. Big advantage due to new special trapezoidal thread which makes it easy to tighten - this prevents the thread from "seizing". The regular and smooth pulling of the fitting by the 2 screws of the Bridge should be careful since pressure marks of the tools’ feet may occur in case of inattention! The respective square bolt knives (8 mm and 10 mm) are included. Also this tool is very well adapted together with our emergency set for broken latch. A 17 mm driver is needed in order to turn the screws lifting the fitting! The “Bridge” differs essentially from the other lifters on the market in the following ways:Assembly of high-value aluminiumDespite new light weight construction extremely loadableVery solid finishingExtremely high durabilityOptimal exertion and distribution of pulling forceBig advantage due to new special trapezoidal threadQuick identification of bolt diameter through millimeter markings    

With this revolutionary tool, plastic windows that are shut can be opened from outside without destroying it. First, by means of a latch opening card or an opening needle, the position of the roller pin or mushroom head lock is determined. Next, the pivot puller is inserted into the rebate, then pushed upwards and "tilted" backwards to grip the pivot / mushroom head lock. With this revolutionary tool, plastic windows that are shut can be opened from outside without destroying it. The first step is to locate the position of the pivot or mushroom head lock by means of a latch opening card or an opening needle. Next, the pivot puller is inserted into the rebate, then pushed upwards and "tilted" backwards to grip the pivot / mushroom head lock. Finally, the provided flat ribbon is inserted through the handle eyelet and "knocked" downwards with a round object, causing the window handle to move into the open position. Attention! Cannot be used with wooden windows, as these always consist of a double rebate. 

Practical use showed that the lead rod is not absolutely necessary. As from now on the estimated Genius is also available in pocket size at an exceptional price: It opens tilt & turn windows from outside. One can only act on the handle, if the window is closed. This genial tool does it from outside. The resistant special materials, selected after long test series, guarantee a successful and danger-minimized application, even during very cold weather.NEW! The new Genius also opens tilt windows with SECURITY FUNCTION (see picture). It may be used universally on all known handle shapes (even HEWI) and with very narrow space (from approx. 10 mm). Delivery includes illustrated instructions, also for bent handles. Light, small, easy to use, resistant, universal, unequalled!Now you can also order the "Genius Repair Kit" through us, consisting of 2 sturdy nylon ribbon cables and 5 repair press clamps that can be used to repair your “Genius” with just a few taps from a hammer (Article: 33969). 

This set of 3 pieces is used to open Tilt& Turn windows with unlocked knobs. Due to its fast and simple application, this window opener is perfectly suitable for all kinds of rescue operations.  Special Features:Easy useFast applicationPerfect for rescue operations (Fire-brigades etc.) weight: 0,510 Kg 

The Woper is a mechanical opening tool for almost all closed windows with wooden, metal or plastic frame and turning handle (not suitable for locked window handles).The opening will be realized without glass breaking by first drilling a hole of minimum 12.5 mm diameter in the window frame with the included special wood drill. The WOPER will be inserted through the drilled hole. Then you place the bent lever arm onto the window handle and open the window by turning the angular handle of the tool. 

ATTENTION: The conversion does not apply to the long shank with tilt arm (see illustration!).From now on, we offer a cost-effective conversion or repair of your old LockOff. However, we need your old LockOff door peephole opener in order to do this.All parts that have proved to be weak points in the past will be replaced by Multipick components at a fixed price, giving you a more robust and durable tool including free return shipping.This is how it works:- Order and pay for the item here in our webshop- Send us your old tool- Allow us approx. 1 week- We will send back your "almost" new piece of equipment (shipping is included for DE).The repair/conversion process can only be carried out in our workshop. 

The door lever is an easy to use tool for lifting up doors. Very suited when using the latch opener set for double-offset doors and in many other situations. 

The (in our opinion) perfect Door Latch Slider The latch opening slider “TFG” completes our selection of tools for the opening of closed but unlocked doors . We are absolutely enthusiastic about the tool’s effectiveness and quality and use the "TFG" on an almost daily basis ourselves. The "TFG" comes in 5 different sizes: 15, 20, 25, 30 & 35 mm, each size optimized for the different types of offset door designs. Experience tells us that there is no better tool for the simple opening of closed but unlocked doors. Put this to the test yourself! The use is incredibly easy! Insert the "TFG" in the gap between door and frame, slide it down to the latch and the door opens.It is made out of highly flexible spring steel and is only as thick as 0.8 mm. The "TFG" can be used effectively almost everywhere. The "TFG" has no sharp edges, and does not cause scratches or other damages on the door or the frame. If the sliding of the "TFG" is made difficult by the sealing strip, lubrication of the "TFG" is very effective.