Lifter Bridge

Opening-Set for single- and double-offset doorsEvery locksmith knows the problem of closed double-offset doors. The new ACE spiral needles, made of high quality spring steel, allow the non-destructive opening of double-offset doors in most cases. The use is very simple: The tool is inserted in the narrow gap between door and frame by turning until it makes contact with the latch. Continued turning pushes back the latch. Usually this process does not cause any damages except a pierced sealing strip. The set consists of four (4) different tools for doors with the lock mounted either on the right or on the left and 2 different material strengths (1.5 and 1.7 mm) for the different types of offset door designs. Of course, the ACE-tools are very well suited for opening simple offset doors as well!For very tightly engaging (closing) double and simple offset doors the ACE-Mini-Set (2 pieces) of only 1.25 mm needle-strength is especially suited. 

The 3.5 mm Door Handle Lasso Tool is a classic opening tool designed for non-destructive entry through slammed doors. Thanks to its slim diameter, it can be guided through the gap beneath the door to reach the interior door handle, which is then operated via the pull cord to depress the handle from the outside. This allows access without damaging the lock or the door. The tool works particularly well on doors with sufficient clearance at the bottom edge (approx. 4 mm or more), or in combination with methods used to create or widen the gap. In many cases, this simple technique provides the quickest solution for opening a door that has merely been slammed shut. Further developed in collaboration with locksmiths and authorities, this tool remains a proven and practical standard solution for professional users who regularly deal with slammed doors. Dimensions: Pull cord length: 156 cm Handle section length: 25 cm Cord attachment section length: 11.5 cm Lever section length: 113 cm  

The popular panic door opener is now available as a set for door opening right and left. No difficult operation anymore thanks to the coverage of all opening directions. Practical and effective! For the opening of closed doors that open to the outside, single-offset doors, i.e. those that can be found in public buildings and emergency exits. In order to insert the tool into the gap between frame and door it is often necessary to broaden this gap using a suction cup or our Multi-Opener. Depending on the door, this application can require different techniques therefore it’s advisable to be prepared for all possibilities! Extending the door gap can accomplished e.g. with a strong siphon, door wedges or a door lever.Special:Spring steel blade, only 1mm thick. Also available individually33800 = Door use from the top right33805 = Door use from the top left  

The LockOff  Door Peephole Opener Kit - Now Being Manufactured By MultipickFrom now on, the LockOff door peep hole opener kit will be manufactured by Multipick in superior Multipick quality. However, we have kept the ingenious basic construction of the tool and simply reinforced the established weaknesses substantially. The Multipick LockOff has finally transitioned into a mature and durable tool, made in Germany.Thanks to its sophisticated system, this high-quality lever tool allows the opening of locked doors, whether single or double-rebated. It is particularly effective for opening self-locking doors.The included auxiliary tools, such as the “Special Pliers” and the “Peephole  Turbo-Helper”, which come in a high-quality shoulder bag for convenient transport and storage, are sufficient to open a door in the “blink of an eye” without causing any damage.In our opinion, this opening tool should be a “must have” component of in the professional equipment carried by emergency key services.Operation: Before using this tool, you should find out which type of door handle is installed. Unfortunately, rotary door knobs are also not operable with this opening tool. First, the length of the LockOff  lever arm must be adjusted. To do this, it's necessary to re-adjust and fix the LockOff rod, adjusting it from the center of the peephole to a position in relation to its distance to the door handle. The angled lever arm rests on the inside door handle. The rubber stopper on its tip prevents damage in case it hits the door. The door handle can be operated by pressing on the outside arm. The calibration of the lever arm in front of the door is very important! If it's too short, the lever slips off the handle before it can be pressed down sufficiently. If it's too long, one cannot generate enough force to press the lever down. In case of misalignment, the inserted LockOff can easily be pulled out and re-adjusted. The door peephole can also be easily removed from the outside with the special cranked pliers; take care to prevent scratches when the pliers slide off onto the door panel. With the LockOff – Peephole Turbo-Helper developed by us, you can remove all standard door peepholes without causing any destructive damage, in no time at all. Simply clamp it into a drill or screwdriver and “unscrew” the peephole with the necessary counter-pressure.Also, from now on, we will be offering a cost-effective modification, or repair  of your old LockOff. at a fixed price. All components with proven vulnerabilities will be replaced by new Multipick components, giving you a more robust and durable tool, including free express return shipping.Images may differ from original. 

This 9-piece set covers a wide range of typical door-opening requirements and provides practical, straightforward solutions for everyday locksmith use. The differently bent latch wires with a diameter of 1.6 mm meaningfully expand existing tool kits and complement standard equipment with versatile application options. The set includes wire needles for double-rebate doors, window rebate geometries, and standard doors, as well as dedicated versions for fire-rated doors, aluminum doors, uPVC doors, and combined uPVC/metal doors. The set is further complemented by a single-rebate wire needle for outward-opening panic doors and a spring wire suitable for working on cylinder clutches as well as for dismantling BKS round cylinders. The spring wire, designed for cylinder clutch work and the removal of BKS round cylinders, features a particularly slim diameter of just 1.4 mm, allowing precise operation even in very confined spaces.