P-Wedge Slider

The popular panic door opener is now available for doors opening to the left and to the right. The easiest direction for opening is to go from the top towards the bottom of the door. Now this is possible with both right and left hand doors. No more complicated handling thanks to the two different directions in which you can now select from, left or right, depending on the direction the door is opening to. Practical and effective!For the opening of closed doors that open to the outside, single-offset doors, i.e. those that can be found in public buildings and emergency exits. In order to insert the tool into the gap between frame and door it is often necessary to broaden this gap using a suction cup or our Multi-Opener. Depending on the door, this application can require different techniques therefore it’s advisable to be prepared for all possibilities! Extending the door gap can accomplished e.g. with a strong siphon, door wedges or a door lever.The tool is made from 1 mm spring steel.  33800 = Door use from the top right33805 = Door use from the top left 

Opening-Set for single- and double-offset doorsEvery locksmith knows the problem of closed double-offset doors. The new ACE spiral needles, made of high quality spring steel, allow the non-destructive opening of double-offset doors in most cases. The use is very simple: The tool is inserted in the narrow gap between door and frame by turning until it makes contact with the latch. Continued turning pushes back the latch. Usually this process does not cause any damages except a pierced sealing strip. The set consists of four (4) different tools for doors with the lock mounted either on the right or on the left and 2 different material strengths (1.5 and 1.7 mm) for the different types of offset door designs. Of course, the ACE-tools are very well suited for opening simple offset doors as well!For very tightly engaging (closing) double and simple offset doors the ACE-Mini-Set (2 pieces) of only 1.25 mm needle-strength is especially suited. 

Our car openers for opening via the inside, in connection with the Lever Suction Cup Set, allow the fast and non-destructive opening of almost every type of car. A newly developed pulling mechanism, mounted in the handle facilitates the exact positioning within the car and a secure pulling of handles, knobs, etc. If necessary the tools can be bent, thus allowing to reach even difficult or hidden locking mechanisms.Power-hook with sharp tip: This tool is often the only possibility to unlock vehicles with special door buttons, handles etc. A small gap is enough to insert the tool into the interior of the car and then control it and make it “bite” the handle/button using the rope.  Controllable hook900 mm length    

The (in our opinion) perfect Door Latch Slider The latch opening slider “TFG” completes our selection of tools for the opening of closed but unlocked doors . We are absolutely enthusiastic about the tool’s effectiveness and quality and use the "TFG" on an almost daily basis ourselves. The "TFG" comes in 5 different sizes: 15, 20, 25, 30 & 35 mm, each size optimized for the different types of offset door designs. Experience tells us that there is no better tool for the simple opening of closed but unlocked doors. Put this to the test yourself! The use is incredibly easy! Insert the "TFG" in the gap between door and frame, slide it down to the latch and the door opens.It is made out of highly flexible spring steel and is only as thick as 0.8 mm. The "TFG" can be used effectively almost everywhere. The "TFG" has no sharp edges, and does not cause scratches or other damages on the door or the frame. If the sliding of the "TFG" is made difficult by the sealing strip, lubrication of the "TFG" is very effective. 

Now even better – even more secure!Using the new grinding disc holder with our special mini grinding discs for steel every grinder becomes a precious tools for low budged and allows the locksmiths to do precise cutting works. Indispensable for the professional for example with broken locks or bolts, padlock cutting etc. The disc holder is made of steel and assures a very precise true running of the discs even with high rotation. The extremely flat head of the fixing screw allows working very close to obstacles. A rubber ring gives a better grip between screw and grinding disc. The 6 mm diameter in the disc socket guarantees a better centric disc guiding when assembling and consequently avoids oscillating.Security advice: While using this tool you have to wear protection glasses!Very important! Don’t confound this tool with cheap and accident-prone products. The arbor diameter is 10 mm, the shaft diameter 6 mm, appropriate with all standard collet in different grinders. Total length: 68 mm.