Thread-pin for pulling mechanism

Double-sided tension wrench Specifications:Side 1 length (outer) = 7.6 mm / Width = 2.3 mmSide 2 length (outer) = 14.0 mm / Width = 3.0 mmMaterial thickness = 1.3 mmTotal length = 76.2 mmWidth: 3.0 mm 

A set of ten key simulators with different shapes, covering the greater part of possible locking combinations. For the efficient, non-destructive opening of many car models and other locks.  

This solid carbide milling burr 4 x 6 x 60 mm is cut off one piece. It distinguishes itself through rough drilling features, due to its deep cuts, which also leads to a good chipping removal.Special features:Due to the reduction of a 6 mm drill burr to 4 mm at the tip, working time is reduced by more than half, for less material has to be cut. A pleasant side effect: the core drawing protection doesn’t have to be destroyed thanks to the small milling burr head diameter. Technical features:Material: Solid carbide Form: cylindrical d1: 4.0 mm I1: 14.0 mm d2: 6.0 mm I2: 60 mm Toothing: crossed toothing for unsiversal use Coating: noneApplication possibilities:     tough and high-strength materialalloyed steel casting synthetic material    universal usagehighest chip removalStrongly recommended for the following materials:BrassCopperCast ironBronzePure steelHardened steelStainless steelHigh-Grade steelTitan 

BLUE-TEC: The new generation of milling burrs especially for locksmiths Better, cheaper and only at Multipick at Top prices - new milling burrs for locksmiths with patent BLUE-TEC coating! Unique lifetimes and performance in all kinds of steel; you will only find this with BLUE-TEC coated milling burrs! And those are available at Multipick, the supplier for locksmiths and more. The particularly efficient grinding and sliding quality of these burrs allow optimal working. Try by yourself! Multipick is able to offer these high quality burrs at a top price! You won’t find Blue-Tec coated millings burrs anywhere at a better price! The unbeatable advantages of the new Blue-Tec milling burrs:Optimised front side + reflexion polishCylindrical shapeMilling burrs especially for LocksmithsMICRO-GRAIN hard metalBLUE-TEC - coatedMade in Germany by KarnaschOnly here at Top-Price! Think milling bits? - Think Multipick! Blue-Tec milling burrs with HP-3 gearing, especially and ideally suited for Locksmiths!High cutting action through cross cutting stylesmooth operationshort chips For use on all ferrous materials such as:cast ironsteel < 60 HRCstainless steel (INOX)nickel basis and titanium alloyAlso copper, brass, bronze Conclusion: The best cutting style for the locksmith!! 

The new Latch Opener Set (2 pieces: 1x 1.5mm and 1x 1.75 mm, made of spring steel wire, with handle) is especially designed for the opening of double-offset doors. After pulling the door out of its frame for a little distance, using the Multi-Opener, Door Lever or Suction Cup etc., the appropriate latch opener is inserted into the gap and pulled up into the direction of the latch. Be careful not to rip out the sealing while doing so. When touching the latch with the tool’s tip, twist the tip of the tool against the latch and the door will open. 

Pick blade for the Original Jackknife-Pickset by MultipickFor perfect supplementing the Jackknife pick sets Exclusive Edition by Multipick we provide 17 different possibilities to personalize your Jackknife pick set according to your wishes and imagination. Often requirements to a tool are very special. So it’s brilliant to have the possibility to assemble a “personalized” tool. The German heavy-duty steel which we use is a highly hardened and tempered metal alloy, unique on the world market. To our knowledge there is no other producer - a part of Multipick -, who uses such a high quality material for pick manufacturing. We are not going to divulge any details, but we are sure that you won’t find the same elsewhere. By precise production in our manufactory changing the blades is “a piece of cake“. The single blade modules made from German high-end steel can be integrated into your Jackknife pick set in a breath. Simply loosen the Allen screw and change the respective blade module. Thus you are optimally prepared for all picking mission, howsoever tricky. Multipick is essentially committed to production of German high-end tools. We disapprove of cheap tools with minor to bad quality, partially produced in low wage countries under inhumane conditions. Multipick clearly speaks up for German high-class workmanship. Therefor our products are elaborately manufactured according to German quality standards. We only guarantee for extraordinarily high material and manufacturing quality on Multipick labelled products! High-end material with perfectly functioning even after many missions - We do not sell steel scrap squeezed into shape, since we develop for the future. Made in Germany - Made in Bonn.  

The (in our opinion) perfect Door Latch Slider The latch opening slider “TFG” completes our selection of tools for the opening of closed but unlocked doors . We are absolutely enthusiastic about the tool’s effectiveness and quality and use the "TFG" on an almost daily basis ourselves. The "TFG" comes in 5 different sizes: 15, 20, 25, 30 & 35 mm, each size optimized for the different types of offset door designs. Experience tells us that there is no better tool for the simple opening of closed but unlocked doors. Put this to the test yourself! The use is incredibly easy! Insert the "TFG" in the gap between door and frame, slide it down to the latch and the door opens.It is made out of highly flexible spring steel and is only as thick as 0.8 mm. The "TFG" can be used effectively almost everywhere. The "TFG" has no sharp edges, and does not cause scratches or other damages on the door or the frame. If the sliding of the "TFG" is made difficult by the sealing strip, lubrication of the "TFG" is very effective.The door latch slider “TFG” is highly flexible but still strong and almost indestructible. Only 0.8 mm thick! Without sharp edges.